![]() Remove tank cover from empty LP gas tank and place on full propane gas tank.Reconnect gas line to LP tank by turning knob clockwise.Repair any problems before attempting to start. Check engine and gas lines for any sign of damage or missing parts.Select the lure output by adjusting the Finetune cover.Place Finetune lure back into holder with holes orienting upward.Remove fresh FineTune lure from package (if necessary).Remove used FineTune octenol lure (if necessary) and properly dispose.Remove Finetune cover by turning counterclockwise.Slide fresh TacTrap in place and remove protective paper.Remove used TacTrap and dispose of properly.Slide WaveDrawer cover onto WaveDrawer.Remove empty tank replace with full LP gas tank.Disconnect LP gas tank per Disconnect LP Gas Tank instructions.Check WaveDrawer and clean (if necessary).Note: While unit is in use, check the following every 2-3 days: SkeeterVac mosquito traps will consume a standard 20# propane gas tank at between 18-30 days depending on the model. To ensure maximum performance and to lengthen the life of your SkeeterVac mosquito trap, perform these steps each time your tank is empty. * Keep the ventilation opening(s) of the propane gas tank area free and clear from debris. ![]() * Do not obstruct the flow of the combustion of LP and the ventilation air. * Keep the SkeeterVac area clean and free from any combustible materials, gasoline, and other flammable vapors and liquids. After 5 minutes of operation, verify LED lights and fan are working properly.Ĭaution: All cleaning and maintenance should be done when SkeeterVac is cool and with the fuel supply disconnected.Ĭaution: DO NOT clean any SkeeterVac part in a self cleaning oven.Ĭaution: This SkeeterVac should be thoroughly cleaned and inspected on a regular basis.Connect propane tank per Connect LP Gas Tank instructions.Disconnect gas tank per Disconnect LP Gas Tank instructions.Move the SkeeterVac to a shady area if at all possible. While this is not normally a problem, on very hot days the SkeeterVac could overheat. Overheat protection switch (heat sensor) turned ONīe sure the SkeeterVac mosquito trap is not in direct sunlight. If fan blades are stopped, turn off propane gas tank per Turning Off Instructions and clean SkeeterVac mosquito trap per Clean and Care Instructions.If fan blade continue to turn on their own, allow SkeeterVac to continue to run.Use a pencil and slowly turn fan blades.Verify the SkeeterVac has been running for at least 10 minutes.Clean SkeeterVac per Clean and Care Instructions.Check ventilation openings and air-inlet to make sure clear of debris.Disconnect propane tank per Disconnect LP Gas Tank instructions.Turn off propane gas tank per Turning Off instructions.Turn on gas valve and check for gas leak by spraying or wiping a water & soapy mixture around the fittings.If still not working refer to Regulator needs to be reset, then repeat steps 1 through 3.Press and hold control valve button and igniter button for up to 3 minutes or until the needle on the engine gauge should begin to move into the Green zone, the LED lights will be flickering and the vacuum fan will be running with air flow out of the engine bottom, indicating ignition is complete.Turn propane gas tank valve slowly to OPEN.Connect propane tank per Connecting LP Gas Tank instructions.Slowly turn propane tank valve to OPEN.After 30 seconds, reconnect propane gas tank per Connect LP Gas Tank instructions.Disconnect gas per Disconnect LP Gas Tank section.Turn off gas per Turning Off instructions.Light SkeeterVac per Lighting Instructions.Perform leak check per Checking for Leaks instructions.Reconnect Regulator/Hose Assembly at SkeeterVac engine.A replacement filter can be ordered here and are easily replaced. The filter may need to be replaced if clogged. Remove Regulator/Hose Assembly at SkeeterVac engine.Disconnect gas per Disconnect LP Gas Tank instructions.Turn off propane tank per Turning Off instructions.If still not working refer to Regulator needs to be reset.Try and light SkeeterVac per Lighting Instructions every 30 seconds until you hear a POP sound indicating ignition.Press and hold control valve button for up to 3 minutes.Connect propane gas tank per Connecting LP Gas Tank instructions.Ĭaution: Keep this appliance area clear and free from combustible materials, gasoline, other flammable vapors and liquids and open flames.If If still not working call our Customer Care at 1.888.753.7137.If you still don't hear a clicking sound replace the igniter.If you do not hear clicking sound replace battery.If you hear a clicking sound, the igniter is working.Turn on propane gas valve and check for gas leak by spraying or wiping a water and soapy mixture around the fittings.
0 Comments
Leave a Reply. |